The Makeover of Two Settees Part Four: The Decking

We have arrived at the final part of this series of DIY reupholstering these two settees, which is replacing the decking or the bottom part of the settee fabric.  I recommend reading all the directions before beginning.

REPLACING DECKING/BOTTOM FABRIC

1.I began this project by cutting out a piece of natural colored duck canvas that covered all but approximately 3 inches on the outside of the seat, as pictured:

I found no need to remove the previous fabric on the bottom because it was in good condition and I could cover it up.

By using the duck canvas, I was able to use less of the vintage hemp linen.  If you notice most upholstered pieced with removable cushions have plain fabric on the bottom pieced together with the fabric that is showing on the outside (and likely the more costly fabric).

2. I then added at least 8 inches of the hemp linen fabric to all the sides, it needed to be enough fabric to cover a couple inches on the seat and to pull through onto to the sides and nail in place with a fold.

I did a lot of estimating and piecing fabric together for this process.  Because of the look I was going for, I was able to piece fabrics together, which made the process much less exact.

3. I sewed the strips of hemp to the canvas with a double seam and created this fabric piece to cover the entire bottom of the seat:

4. Next up is tucking the fabric around the legs and arms of the settee.  This is the trickiest part in my opinion.  Proceed carefully.  I love using these scissors for the process of slowly cutting into the fabric so that the fabric lies flat, but not too much that any cuts in the fabric are visible.  I always try to over estimate on the fabric needed and then make more cuts where in order to get the placement right.

5. Once I am pleased with the way the fabric is placed and tucked under, I flip up the front strip, and do a quick whip stitch at the seam on the bottom to the fabric on the seat.  I use a curved needle and upholstery thread to do this.

6. Now that is secure, it is time to tack the outside bottom to the frame.  I like using carpet tacks for this and I also like my lightweight upholstery hammer to minimize damage to the wood frame.  I fold the fabric under so no raw edges are exposed and hammer into place.

This is another case where I did not mind everything not being quite exact due to the slightly rustic look I was going for.  There were times I need to add a fold to the fabric to get it to lie flat and I was just fine with that.

AND WE ARE DONE

Remember where we started from?

Thank you for checking out this post.  Feel free to contact me with any questions at pennyandivydecor@gmail.com.

 

 

 

Reupholstering thrift store chair

I thought I would offer a bit of a behind the scenes look at reupholstering this thrift store chair.  I had not done a big project like this in some time, it reminded me that I really enjoy reupholstering pieces and that it takes quite a bit of time.

Here is a picture of how I found the chair although it did come with a seat cushion. I am not entirely sure why I didn’t include it in the photograph, I took it several months ago and that is too long ago for my memory to recall such details :). Although I do remember shopping at the thrift store when this was brought out onto the floor by one of the workers and staking my claim on it as quick as possible.  There is nothing like thrift shopping to bring out my most assertive self. I was drawn to its shape and upon inspection I found it to be very sturdy. I am often tempted in second hand projects that aren’t particularly sturdy, but they can be more trouble than they are worth.  There are lots and lots of potential projects out there, you can find a sturdy one, it will be worth the wait.

This chair sat in my basement for a while, like nearly 2 years.  So in my head it went through a variety of plans.  I actually sanded down the finish a couple months ago and sealed with wax. It was a nice finish, but when I finally decided upon using this vintage hemp mattress cover that I purchased from the shop, Parna, I thought it needed to be painted white.  I painted the wood two coats of  Miss Mustard Seed Milk Paint Linen after a light sanding, I sealed it with a layer of tough coat.

To avoid reinventing the DIY wheel I am going to direct you to Miss Mustard Seed’s blog that inspired and taught me how to reupholster a French Style chair, . She offers a great detailed tutorial if this is a project you would like to tackle.  AND YOU CAN TACKLE IT!!! 

For this project I was so glad that the fabric that I stripped from the chair remained intact so I could use it as a pattern.  It is generally good practice to always do this,  but in this case it especillay helped me line up the stripes and stitching just so. On a side note something very special about this kind of vintage fabric is the hand stitching.  In my work I like to celebrate time and person who carefully did these quality stitches that have lasted decades.  It adds so much meaning to these beautiful textiles, I often wonder who this seamstress they might be? And in what setting did work? I wanted these stitches found running down the front of the chair and lining it up worked out great with a pattern.

Next I like to tack up my pieces of fabric to get a visual on placement before I reach the staple gun level of commitment.

Here I am happily working on the back of the chair:

*note all the visitors I have wondering about dinner.  I had hoped they might forget, but they never do.*

After the back of the chair was done I took on the cushion cover.  Cushion covers have given me the most headaches in reupholstery.  It has taken me a lot of practice to get somewhat efficient and confident in sewing them.  I have even hired a sewing instructor TWICE to work along side me to give me pointers.  However I totally think I beginner can sew one. Absolutely. There just could possibly be a bit more moments of frustration, at least that was my experience. But if you are mentally prepared for frustration, hiccups often don’t turn into frustration.  So by all means beginners go for it!  My first cushions turned out fine in the end, but it took A LOT of patience. I am not trying to be a downer or discourage anyone, quite the opposite.  I just don’t want to romanticize the process so that if someone tries this out and it doesn’t turn out the first time they know they are not alone. This is a really good tutorial done by Peg Baker and she is very precise, maybe I would have had more luck when starting out if I had followed a her tutorial. In her tutorial she uses piping, for the deisgn of this cushion I liked it without piping. Also she teaches how to put a zipper closure, I like buttons and use those instead.  The buttons take a bit more time, and more fabric is needed for the overlap but it is worth it for me.  Also I have found an important step in making a cushion with this hemp linen is adding a bit of padding.  I really like a full looking cushion and the woven fabric has a lot of stretch to it, I always end up adding a layer or two of dacron.  This cushion was already very full, but it needed a little more padding.  I cut a piece that was just about half the size of the top of the cushion and then I cut a piece to the exact size of the entire top of the cushion.   I put both pieces in place on top of the cushion with the smallest one under the larger one.  I like the bit of cozy fullness it added to the seat. 

When I put the cushion back on is when I had my ahhhhhh moment, the chair was starting to come together.  It takes a while to get to this point with upholstery, but it is so sweet and worth the wait to feel like your vision is coming to life.  Also you may notice on the bottom left there is a stripe that I patched in.  I felt like it needed one more stripe and that is the beauty of this pieced togther look of the fabric is that it gives freedom to add patches.

Next up was the bottom of the seat.  I used modern canvas for the part of the seat that would be covered by the cushion, this is fairly typical, but also I needed to because I was running out of the vintage hemp fabric.  To be honest here, this part took me the better part of a day.  It is tricky because you have to make cuts to fit around the legs and arms of the chair so that the fabric is smoothed down in place, but you can’t cut too much then you are left with too little fabric. In someplaces the trim can help cover some small spaces in the fabric, eventhough it is just a half an inch it can make all the difference.  I am glad that I took my time with this seat, in the end it turned out well.

When I put the cushion back on is when I had my ahhhhhh moment, the chair was starting to come together.  It takes a while to get to this point with upholstery, but it is so sweet and worth the wait to feel like your vision is coming to life.  Also you may notice on the bottom left there is a stripe that I patched in.  I felt like it needed one more stripe and that is the beauty of this pieced togther look of the fabric is that it gives freedom to add patches.

Next up was the bottom of the seat.  I used modern canvas for the part of the seat that would be covered by the cushion, this is fairly typical, but also I needed to because I was running out of the vintage hemp fabric.  To be honest here, this part took me the better part of a day.  It is tricky because you have to make cuts to fit around the legs and arms of the chair so that the fabric is smoothed down in place, but you can’t cut too much then you are left with too little fabric. In someplaces the trim can help cover some small spaces in the fabric, eventhough it is just a half an inch it can make all the difference.  I am glad that I took my time with this seat, in the end it turned out well.

The last parts to the chair left were the fabric for the arms and the trim.  Picking the right trim can stress me out. It can a make or break part of the entire piece.  I feel like sometimes its hard to find a trim that looks like it belongs with the fabric and doesn’t overpower or detract from it.  For this chair I wanted it to blend, and in order to get the color just right I need to make my own with the same fabric.  I made my own double welting.  And here is yet another tutorial that I did not write, thank you Miss Mustard Seed. Then I secured the trim with a glue gun.  I used a small piece of fabric to glue into place where the ends met, I tried to place these parts in inconspicious areas. On the arms where it was visiable I added a button, because why not?

And she DONE and avaliable for purchase with local Milwaukee pick up. All the details are on the shop page

For quick reference here is a list of the tools I use:

Surebonder Staple Gun

Rigid 6 Gallon Air Compressor

T50 Staples I like to have a couple different sizes handy, I often start with the smaller ones so I can remove them if needed and adjust things. Then when I am ready to commit, I bring out the larger ones.  Be sure you get the right kind of staple for your staple gun. 

Upholstery Webbing

Upholstery Webbing Tool

Detail Scissors

Please let me know if you have any questions or success stories, my email is pennyandivydecor@gmail.com.

*Disclosure: This post contains affiliate links at no additional cost to you.*

Please subscribe to Penny & Ivy's email list to receive updates on future sales and a bonus 10% off welcome coupon code